LDX-026A Manufacturers customize large circular saw blade automatic
grinding machine
How to use multi-blade saw gear grinding machine:
1,First of all, the grinding wheel lift is adjusted to the lowest,
the saw blade is installed on the saw blade seat, a good pressure
plate, turn the handwheel, the saw blade is driven by the lead
screw to move up and down the saw blade is adjusted to more than
30~50 mm of the pressure head, and the pressure head is compressed.
2,Adjust the serrated position at the end of the gear shift and
align the grinding wheel with the serrated saw blade. Then adjust
the grinding wheel to the grinding * position to start grinding.
3,Grinding wheel Angle adjustment: to adapt to grinding saw blades
with different serrated front angles. The Angle of the wheel
mounting plate can be adjusted. The method is to loosen the two
bolts of the mounting seat plate of the grinding wheel holder (do
not remove the nuts) and then rotate the grinding wheel holder in a
clockwise direction. Turn so that the front end of the grinding
wheel, when the saw blade feed grinding, can contact the entire
plane of the front corner of the tooth (from the tip of the tooth
to the root of the tooth).
Circular saw blade common problems and solutions:
1,First check whether the equipment is placed high or uneven, check
the bad bearing of the equipment, the machine shell should be kept
intact, the grinding wheel of the equipment is not eccentric and
other problems, and finally check whether the gear is intact and
whether the bearing seat is worn; If there is still no way to solve
the problem, immediately contact the manufacturer for processing.
2,Most of this situation is the line problem, should immediately
cut off the power supply, check the line, test whether the voltage
is stable, whether the power supply is normal, whether the ground
line is linked, there is no influence on the voltage equipment
nearby, there is also a situation, that is, the equipment itself,
see whether the saw blade items stuck, or other parts should also
be checked; If there is a problem with the equipment itself, this
needs to be checked by a professional.
3,Most of the possibilities are bearings, such as eccentric
grinding wheel, damage, gear damage, etc. Such hardware damage
should be contacted by the supplier for repair or replacement.
| Technical parameters: |
| Processing saw blade diameter range: ￠300- ￠ 1800mm |
| Saw blade aperture: ￠ 10-220mm |
| Saw blade thickness (steel plate): 1-12mm |
| Tooth pitch: 7-120mm |
| Tooth surface angle: 5 degrees to+30 degrees |
| Tooth top back angle: 6-45 degrees |
| Left and right inclination of teeth: tooth tip/tooth surface 45
degrees |
| Blade grinding stroke range: maximum 25mm (adjustable) teeth/minute |
| Grinding speed: 0.5-6mm/s |
| Working speed: maximum 20 teeth/minute |
| Grinding wheel size (outer diameter x hole): (￠ 125mm x ￠32mmX1mm) |
| Negative chamfer grinding: -27 degrees |
| Grinding head rotatable angle: 90 degrees and 180 degrees |
| Grinding wheel linear speed: 26m/s |
| Flow rate of coolant water pump: 501/min |
| Volume of coolant cylinder: 85L |
| Total power: 2.2 kW |
| Voltage: three-phase 380v |
| Mechanical weight: 1200KG |
| Mechanical dimensions (length x width x height): 1800X1400X1800mm |
| Technical features: |
| The design of this machine refers to the characteristics of similar
domestic and foreign models, absorbs and analyzes the advantages of
the same type, and makes some functional improvements. This
equipment is specifically designed for grinding large alloy saw
blades. |
| 1. Pre set multiple sets of tooth profiles for one click
multifunctional operation. |
2. The flat teeth of the ladder can be completed in one go, with
CNC grinding and any tooth shape, which can increase efficiency by
three times; Improved gear extraction operation to improve accuracy
and extend service life.
|
